Polyketone (POK): properties and injection molding

POK is a semi-crystalline aliphatic polyketone with high impact strength, low wear, good chemical resistance and low moisture uptake. Pros, cons and molding.

Bemar Plast Team. Updated on .

POK (aliphatic polyketone) is a semi-crystalline engineering plastic made from carbon monoxide and ethylene, with a small share of propylene. It combines high impact strength, a low coefficient of friction, good chemical resistance and much lower moisture absorption than nylon. It is injection molded into gears, connectors and parts exposed to fuels, oils or coolants, often as an alternative to POM and nylon (PA).

History

Alternating aliphatic polyketones became industrially viable with palladium-based catalysts, which link carbon monoxide and ethylene in a regular sequence. Shell brought the material to market in the 1990s under the Carilon brand and discontinued production in 2000.

POK returned to industrial-scale supply when the South Korean group Hyosung started a production plant in Ulsan, South Korea, in 2015, under the POKETONE brand. Since then other compounders have introduced reinforced and modified grades based on the same polymer.

Structure and grades

POK is an aliphatic polymer: the chain contains no aromatic rings, but a ketone group (C=O) alternating with each ethylene unit. The polar ketone groups attract each other between neighboring chains, which explains the high crystallinity and the solvent resistance. It should not be confused with aromatic polyketones such as PEEK, a different family with much higher service temperatures and cost.

There are two main forms:

  • Copolymer of carbon monoxide and ethylene: highly crystalline, with a high melting point and a narrow processing window.
  • Terpolymer of carbon monoxide, ethylene and propylene: a small share of propylene lowers the melting point to about 220 °C (428 °F) and makes the material processable on standard injection molding machines. This is the form used in commercial grades.

Grades differ in melt flow (injection molding or extrusion) and formulation: unfilled, glass fiber reinforced, mineral filled, modified for friction and wear, and flame retardant.

Properties of POK: advantages

  • Impact strength: higher than POM and comparable to nylon, with minimal change between dry and humid conditions.
  • Wear and friction: low coefficient of friction and low wear, including plastic-on-plastic contact; the POK-POM pairing is one of the most studied combinations for gears.
  • Chemical resistance: good resistance to fuels, oils, aliphatic and aromatic hydrocarbons, salt solutions, and weak acids and bases.
  • Hydrolysis resistance: reinforced grades retain their properties in hot water-glycol better than PA6 and PA66, which is why POK is considered for cooling circuits.
  • Low moisture absorption: far below PA6 and PA66, so dimensions and mechanical properties change little with ambient humidity.
  • Barrier properties: used in some extrusion grades.
  • Fast crystallization: allows short injection molding cycle times.
  • No formaldehyde release: unlike POM, thermal degradation of POK does not release formaldehyde.
  • Weldability: grades are available for laser welding and infrared welding.

Properties of POK: disadvantages

  • UV exposure: resistance to sunlight is poor; outdoor parts need stabilized or pigmented grades.
  • Thermal stability in the barrel: if the material stays too long at high temperature it can crosslink or degrade, with rising viscosity and dark specks on the part.
  • Strong acids and bases: resistance drops with concentrated acids and bases, especially at elevated temperature and with prolonged exposure.
  • Temperature: the melting point is lower than that of PA66; loads at elevated temperature require reinforced grades and testing on the part.
  • Appearance: gloss and scratch resistance are lower than those of engineering nylons, and coloring requires a masterbatch with a compatible carrier.
  • Flammability: electrical applications with flame retardancy requirements need dedicated flame-retardant grades.
  • Availability: there are few producers, so the grade range, pricing and lead times should be checked at the start of the project.

Processing and injection molding

POK can be processed by injection molding, extrusion and, with dedicated grades, pellet-extrusion 3D printing. In injection molding it behaves like other semi-crystalline engineering plastics, with a few specific points to watch.

Drying

POK is only slightly hygroscopic and often does not need the long drying cycle required for nylon. If the pellets have picked up moisture, for example after storage in open bags, producers specify drying at a moderate temperature: time and temperature should be taken from the datasheet of the grade. In our molding department every line has a dehumidifying dryer with molecular-sieve units, wheel or twin-tower type.

Process parameters

  • Melt temperature: keep it within the window specified by the supplier and avoid overheating, because POK degrades above the recommended limits.
  • Residence time: keep it short. Size the barrel to the shot weight and empty it during stops.
  • Mold: fast crystallization allows short cycles; correct mold temperature control ensures uniform crystallinity and dimensional stability.
  • Shrinkage: as with all semi-crystalline materials, shrinkage depends on formulation, wall thickness and flow direction, especially in glass-filled grades; it has to be accounted for in mold design.

Additives and reinforcements

  • Glass fiber: increases stiffness, strength and heat resistance.
  • Mineral fillers: reduce warpage and improve flatness.
  • Internal lubricants: further improve friction and wear in sliding parts.
  • UV stabilizers and carbon black: required for outdoor use.
  • Flame retardants: for electrical components with flame retardancy requirements.

POK vs POM vs PA66

PropertyPOKPOMPA66
StructureSemi-crystallineSemi-crystallineSemi-crystalline
Melting pointAbout 220 °CAbout 165-175 °CAbout 260 °C
Moisture absorptionLowVery lowHigh
Impact strengthHighMediumMedium when dry, higher when conditioned
Wear and frictionVery goodVery goodGood
Fuels and oilsGoodGoodGood
Grade availabilityLimitedWideWide

This comparison is indicative: actual properties depend on grade and formulation and should be checked on supplier datasheets.

Applications of POK

  • Automotive: cooling circuit and thermal management components, parts in contact with fuel, actuator gears.
  • E-mobility and electrical: connectors, cable ducts and battery management components, using flame-retardant grades.
  • Machinery and automation: gears, rollers, bushings and slides, including pairings with POM.
  • Furniture: mechanisms and components of seating and adjustment systems exposed to impact and wear.
  • Oil and gas: clamps and fasteners exposed to hydrocarbons.

Evaluating POK for your part

POK is worth considering when a POM part risks cracking under impact, or when a nylon part loses dimensional stability because of humidity or contact with water-glycol. For POK we evaluate the material together with your engineering team: we start from the part requirements, compare it with the alternatives and define the mold and the injection molding process.

Frequently asked questions

What is POK?

POK is an aliphatic polyketone, a semi-crystalline engineering plastic made by copolymerizing carbon monoxide and ethylene, usually with a small share of propylene. It is used for technical parts that need impact strength, wear resistance and chemical resistance, such as gears, connectors and parts exposed to fuels or coolants.

How does POK compare with POM (acetal)?

POK has higher impact strength than POM and comparable wear resistance, which makes it an option for gears and sliding parts that also take impact loads. Unlike POM, it does not release formaldehyde when it degrades thermally. POM remains more widespread, with more producers and grades.

Does POK absorb moisture like nylon?

No, POK absorbs far less moisture than PA6 and PA66: at equilibrium with ambient air, roughly a quarter of the amount absorbed by an aliphatic nylon such as PA66. Dimensions and mechanical properties therefore change little between dry and humid conditions, while nylon loses stiffness and gains impact strength as it absorbs water.

Does POK need drying before injection molding?

It depends on the grade and on how the pellets were stored: POK is only slightly hygroscopic, but producers may specify drying at a moderate temperature if the material has picked up moisture. The conditions on the supplier datasheet apply.

What are the limitations of POK?

The main limitations are poor UV resistance without stabilizers, sensitivity to long residence times in the barrel and limited resistance to strong acids and bases at elevated temperature. Supply is also a factor: there are few POK producers compared with POM and nylon.

How do you evaluate POK for a new part?

Start from the part requirements: loads, impact, friction, fluids in contact, temperature and exposure to sunlight. We evaluate the material together with your engineering team and compare it with alternatives such as POM and PA66 before defining the mold and the injection molding process.

Send us your drawing, and we will tell you how to mold it

We reply with a technical assessment and a quote. To prepare them, we need three pieces of information about your component.

  1. The part

    The 2D drawing or 3D model of the component.

    • STEP
    • IGES
    • PDF
  2. Material and annual volume

    The required material, or the part's operating conditions if the material has yet to be chosen. Then the approximate annual volume.

  3. Cosmetic requirements and tolerances

    Visible surfaces, color and finish, and the critical tolerances to be met.

If you do not have all the data yet, write to us anyway: we will define it together.

Hours
Monday–Friday, 8 a.m.–6 p.m. Italian time (2 a.m.–noon ET)